My dear reader, I would like to apologise for my extended absence from the wonder world of virtual woodworking via the internet. You would find the reasons quite boring so let’s not waste any time nor effort ruminating on such drivel. This instalment of an apparently mammoth series will concern itself with the addition of the third and final layer of the so-called trapezoid leg. You can find earlier posts in this series here.
Seeing that the third layer would ultimately close up the internal workings of the whole construction, I took the opportunity to unscrew the second layer’s three ‘cross members’ (for lack of a better term). As you should be able to observe in the photos below, the old school mild steel wood screws received a coat of beeswax. This was accomplished by melting a block of wax in a small tin containing these traditional fasteners. The idea with this is that the wax should reduce the effort required to seat the screws and at the same time providing a layer that would resist future corrosion.
The screws were then seated after the surfaces that is supposed to be able to slide ever so slightly with the changes in ambient humidity over the years, were rubbed with beeswax. Whether this is useful (or possibly the opposite) I do not know, but I tried it anyway. Therefore I would urge you to ask someone who knows before following suite. Maybe some of our more experienced and properly trained cadres could assist in the matter.
Seeing that the plan was to fix the third and final layer using panel pins I had to fashion a custom punch to seat the nails below the surface of the wood. A short section of a round file which I picked up somewhere served perfectly well for this purpose. It was shaped carefully (not to take the temper out of the hardened steel) on a bench grinder to fit the head of the panel pin to a T. There are some picks further down to show the business end of my new redneck punch.
As is so common here in Africa, I also had to modify the panel pins somewhat to serve my purpose. In order to allow layer one and two to be able to move relative to each other, these panel pins had to stop short of layer one. In other words they should only fix layer three to the cross members of layer two. That was accomplished by snipping off the required amount, followed by resharpening on the bench grinder.
The two Kershout strips were fitted first, as they needed to be absolutely spot on given the fact that they mirror the spindles of the so-called Windsor leg. Kershout seems to enjoy spending time off the Janka hardness charts (literally and figuratively) so it hard to say where it rates in comparison to better known species, but let’s just say it tends to take exception when a nail wants to upset it’s feng shui. For that reason I had to drill shank holes for each panel pin, which allowed the shank through and only caught the slightly wider head. This way the panel pins were more inclined to retain it’s linear configuration and the Kershout refrained from flexing it’s muscles.
As discussed in earlier posts, the third layer only needs to add another 8 mm for the trapezoid leg to reach it’s intended thickness of 44 mm. Therefore I decided to challenge my new bandsaw with fairly wide re-sawing in very hard Witpeer. Of course that also allowed me to introduce visual interest by means of a book-matched arrangement of the various pieces.
In order to do that I needed one flat, square and twist-free face side and face edge.
The resultant 8 mm stock were then fitted from the centre of the leg towards the outside. I again used the hitherto unproven technique of rubbing beeswax on the surfaces that is supposed to be able to slide.
I used a no. 78 and a no. 10 Stanley rabbet plane to cut the rabbets that hides the space allowed for movement.
The book-matched pattern is already vaguely apparent.
All the sides were then worked flush.
By hand plane along the grain …
… and by track saw followed by hand plane across the grain.
The small cavities created by seating the panel pins below the surface of the wood were filled with a concoction conjured up by mixing very fine wood dust (of the same wood of course) and epoxy.
Once the elixir had time to set I did a preliminary round of surface preparation.
As you can see the book-matched pattern is starting to emerge nicely. Once it receives oil it should be positively stunning.
Even the opposite side is starting to display a certain je ne sais quoi.
The edges were then treated to some hand beading to hide the laminations.
As you can see it worked a charm.
In our next instalment we will move on to laminating the various boards that was chosen (many moons ago) for the top.